We have encountered this great article about How to Install a Bathtub Yourself below on the internet and believe it made sense to talk about it with you in this article.
Installing a bath tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, and also occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently easily accessible, the project can relocate speedily; if you need to open a wall to get rid of the old tub and place the brand-new bath tub, the job is a lot harder. In either instance, the job is within a house handyman's abilities, although you will certainly require an assistant to leave the old tub as well as embeded in the brand-new one. Make sure you have qualified yourself for the task as well as are comfortable attempting it. Instead of working with a specialist to take control of a halfway-completed job, it is far better to think about using one prior to you begin. Opportunities are you may require a professional plumber to make tube connections.
This short article will aid you mount a brand-new tub in your restroom if you have already acquired a brand-new tub and do not need to change the arrangement of your previous water supply pipelines.
Your tools and also material list must comprise the following:
Planning for the Setup
First of all, the supporting structure provided with the bathroom needs to be fitted (if called for) according to the manufacturer's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to see to it that if the tap comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to stop strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its last position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you should do is separate the water supply. After doing so, switch on the taps to drain any type of water continuing to be in the system. The procedure of removing the existing faucets can be rather bothersome due to the restricted accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the staying water that will certainly originate from the pipes. As soon as the supply pipelines have actually been removed, use the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning during this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any old securing compound.
Prior to carrying on to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the tub in the required position. The wood boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four small factors.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by checking the level as well as changing the feet on the tub until the spirit level reads degree.
To install taps, fit the bottom of the furthest flexible tap connector to the ideal supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Switch on the water and examine all joints and also brand-new pipework for leaks as well as tighten them if necessary. Fill the bathtub as well as additionally inspect the overflow outlet and the regular outlet for leakages.
Lastly, repair the bathroom paneling as explained in the supplier's instruction manual. Tiling and also sealing around the bath tub should wait up until the tub has actually been made use of at least once as this will settle it right into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the faucet and also the other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will need minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washing machines are in area between the faucet as well as the sink. Protect the faucet in position with the maker supplied backnut. Once the faucet is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The previous type needs to be connected to the tap finishes initially, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bath satisfies the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to fracture a rigid seal, triggering the water to permeate the wall surface in between the bathroom and the tiling, bring about problems with dampness as well as feasible leaks to the ceiling below.
You can select from a range of coloured sealants to blend in your components as well as installations. They are offered in tubes and also cartridges, and are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of drenched paper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to enable the motion experienced when the bathtub is in use. The sealant can fracture rather early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently available on the market. It is recommended to fit the tiles utilizing waterproof or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our part on A Step-by-Step Guide to Installing a Bathtub. Thank you so much for taking time to browse our article. Don't hesitate to take a moment to promote this post if you enjoyed it. Thank-you for going through it.
Hot water gone? Dial here.